Laboratory Fume Hood Airflow: Face Velocity, Containment and Testing
Release time:
2026-11-11
Laboratory Fume Hood Airflow: Face Velocity, Containment and Testing

Introduction
Laboratory fume hood airflow is one of the most important factors affecting the safety and performance of laboratory ventilation systems.
A properly designed fume hood uses controlled airflow to capture hazardous fumes, vapors, gases, and airborne contaminants generated during laboratory operations. However, simply installing an exhaust fan or achieving a specific air velocity does not guarantee effective contaminant containment.
Factors such as face velocity, sash position, airflow distribution, exhaust volume, room ventilation, and equipment placement all influence fume hood performance.
For laboratory designers, engineers, facility managers, and equipment purchasers, understanding these factors is essential when selecting and installing laboratory fume hoods.
In this guide, we will explain how laboratory fume hood airflow works, what face velocity means, how airflow is calculated, which factors affect containment performance, and how fume hood airflow is tested according to recognized industry standards.
1. How Does Laboratory Fume Hood Airflow Work?
A laboratory fume hood operates by drawing air through its front opening and directing contaminated air away from the operator.
The airflow creates an inward movement of air that helps prevent hazardous airborne contaminants from escaping into the laboratory.

A typical ducted laboratory fume hood operates through the following process:
Step 1: Air Intake
Room air enters the fume hood through the front sash opening.
Step 2: Contaminant Capture
Airflow helps capture fumes, vapors, and other airborne contaminants generated during experiments.
Step 3: Airflow Distribution
Internal baffles and the exhaust plenum help distribute airflow throughout the enclosure.
Step 4: Exhaust Collection
Contaminated air is collected through the exhaust outlet.
Step 5: Exhaust Discharge
The exhaust fan transports contaminated air through the ductwork to a suitable discharge location.
Main Components Affecting Airflow
Front sash and working opening
Internal airflow baffles
Exhaust plenum
Exhaust outlet
Exhaust ductwork
Exhaust fan
Airflow monitoring system
Laboratory supply air system
All these components work together to maintain suitable airflow and containment performance.
2. What Is Face Velocity in a Laboratory Fume Hood?

Face velocity is the average speed of air entering the fume hood through its open front working area.
It is commonly measured in:
Feet per minute (FPM)
Meters per second (m/s)
Face velocity is an important parameter when evaluating laboratory fume hood airflow.
It helps determine whether sufficient air is entering the enclosure under specified operating conditions.
Typical Face Velocity Range
For many conventional laboratory chemical fume hood applications, commonly used design targets are approximately:
80 FPM (0.41 m/s)
90 FPM (0.46 m/s)
100 FPM (0.51 m/s)
However, these values are not universal safety requirements.
The appropriate face velocity depends on the hood design, chemical hazards, sash position, room airflow conditions, and verified containment performance.
Some well-designed fume hoods can achieve suitable containment at lower velocities, while other configurations may require different operating conditions.
A higher face velocity does not automatically mean better protection. Excessive airflow can create turbulence and potentially interfere with containment.
The final operating target should be established through the hood manufacturer's specifications, project requirements, and appropriate performance testing.
3. How to Calculate Fume Hood Face Velocity
Face velocity is calculated by measuring the airflow speed across the fume hood's front opening.
The average face velocity is determined from multiple measurement points distributed across the working opening.
Face Velocity Formula
Average face velocity is calculated as:
V = (V₁ + V₂ + V₃ + ... + Vₙ) / n
Where:
V = Average face velocity
V₁, V₂, V₃ = Individual velocity measurements
n = Total number of measurement points
For example, if five measurement points produce the following readings:
| Measurement Point | Air Velocity |
|---|---|
| Point 1 | 0.45 m/s |
| Point 2 | 0.48 m/s |
| Point 3 | 0.47 m/s |
| Point 4 | 0.46 m/s |
| Point 5 | 0.49 m/s |
Average face velocity:
(0.45 + 0.48 + 0.47 + 0.46 + 0.49) / 5
Average = 0.47 m/s
This provides an average measurement for the tested sash opening.
The actual measurement grid and acceptance criteria should follow the applicable testing procedure and project specification.
Relationship Between Face Velocity and Exhaust Volume
Face velocity and exhaust airflow volume are closely related.
For a simplified calculation:
Q = V × A
Where:
Q = Exhaust airflow volume (m³/s)
V = Average face velocity (m/s)
A = Open sash area (m²)
For example:
A fume hood has an opening width of 1,200 mm and a sash opening height of 500 mm.
Opening area:
1.2 × 0.5 = 0.6 m²
Assuming an average face velocity of 0.5 m/s:
Q = 0.5 × 0.6
Q = 0.3 m³/s
Convert to cubic meters per hour:
0.3 × 3,600 = 1,080 m³/h
Therefore, the estimated airflow through the opening is 1,080 m³/h.
This is a simplified airflow calculation. Actual exhaust fan selection must also consider duct resistance, fittings, pressure losses, control arrangements, and the complete ventilation system.
4. What Is the Difference Between Face Velocity and Exhaust Volume?
Face velocity and exhaust volume are related but describe different aspects of fume hood airflow.
Face Velocity
Face velocity measures how quickly air enters through the open front of the fume hood.
It is generally expressed in FPM or m/s.
Exhaust Volume
Exhaust volume measures how much air the exhaust system removes over a specific period.
It is generally expressed in:
m³/h
CFM
L/s
Comparison
| Parameter | Face Velocity | Exhaust Volume |
|---|---|---|
| Definition | Speed of incoming air | Quantity of exhausted air |
| Unit | m/s or FPM | m³/h or CFM |
| Measurement | Across sash opening | In exhaust duct or system |
| Main Purpose | Evaluate inlet airflow | Determine exhaust capacity |
| Influencing Factors | Sash opening and airflow distribution | Face velocity and opening area |
Both parameters should be evaluated when designing a laboratory fume hood ventilation system.
5. Factors That Affect Laboratory Fume Hood Airflow

Even a properly manufactured fume hood may experience poor containment if the surrounding laboratory conditions are unsuitable.
Several factors can affect airflow performance.
5.1 Sash Opening Height
The sash opening directly affects the front opening area.
When the sash is raised, the opening area increases.
If the exhaust volume remains constant, average face velocity generally decreases.
When the sash is lowered, the opening area becomes smaller, and average face velocity may increase if the exhaust volume remains unchanged.
This is why sash position is an important factor in airflow control.
5.2 Internal Airflow Baffles
Airflow baffles help distribute air through the fume hood enclosure.
Poorly designed or obstructed baffles may create uneven airflow patterns and stagnant areas.
Proper baffle positioning helps improve airflow distribution and contaminant removal.
5.3 Exhaust Fan Performance
The exhaust fan must provide sufficient airflow against the resistance of the entire duct system.
Important factors include:
Fan capacity
Static pressure
Motor power
Fan speed
Duct length
Duct diameter
Number of bends
System resistance
Selecting a fan based only on its rated airflow without considering static pressure may result in insufficient actual performance.
5.4 Laboratory Room Ventilation
The room ventilation system influences the airflow entering the fume hood.
Insufficient replacement air or poorly balanced room ventilation can affect hood performance.
The laboratory supply and exhaust systems should be designed together.
5.5 Cross-Drafts
Cross-drafts are unwanted air currents moving across the front opening of a fume hood.
They may be caused by:
Air conditioning outlets
Open doors and windows
Pedestrian traffic
Nearby ventilation equipment
Other exhaust systems
Strong cross-drafts can disturb inward airflow and increase the risk of contaminant escape.
5.6 Equipment Placement
Large equipment inside a fume hood can obstruct airflow.
Incorrect positioning may create turbulent areas or interfere with the internal airflow pattern.
Equipment should be arranged to avoid blocking the rear baffles and exhaust openings.
5.7 Operator Movement
Rapid movements near the fume hood can disturb airflow around the sash opening.
Operators should avoid unnecessary movement directly in front of the working opening.
5.8 Temperature Differences
Hot equipment and chemical reactions can generate thermal plumes that influence airflow inside the enclosure.
Fume hood designs intended for high-heat applications require special consideration.
6. Laboratory Fume Hood Airflow Control Systems

Different fume hood ventilation systems use different methods to maintain appropriate airflow.
6.1 Constant Air Volume (CAV)
A Constant Air Volume system maintains a relatively fixed exhaust airflow volume during operation.
When the sash position changes, the open area changes while the exhaust volume remains approximately constant.
Advantages:
Relatively simple system design
Stable exhaust volume
Straightforward control arrangements
Suitable for many conventional laboratory installations
Limitations:
Face velocity changes with sash opening
Exhaust energy consumption may remain relatively high when the sash is closed
Requires suitable room replacement air
6.2 Variable Air Volume (VAV)
A Variable Air Volume system adjusts exhaust airflow according to changes in sash position or another control signal.
When the sash is lowered, the system can reduce exhaust volume while maintaining the designed operating conditions.
Advantages:
Can reduce exhaust air volume when the sash is closed
May reduce heating and cooling energy consumption
Supports more flexible laboratory ventilation control
Can respond to changing operating conditions
Limitations:
Requires more sophisticated control components
Needs proper calibration
Requires coordination with the building ventilation system
Incorrect control settings may affect containment performance
6.3 Bypass Airflow System
A bypass fume hood includes an additional airflow path designed to help manage changes in airflow as the sash moves.
Depending on its design, the bypass opening can help reduce excessive increases in face velocity when the sash is lowered.
Bypass arrangements must be engineered and tested as part of the complete fume hood system.
CAV vs VAV Comparison
| Comparison | CAV System | VAV System |
|---|---|---|
| Exhaust Volume | Relatively constant | Automatically adjustable |
| Sash Response | Limited airflow adjustment | Responds to sash position or control signals |
| Energy Efficiency | May have higher exhaust energy use | Potential for energy savings |
| Control System | Simpler | More complex |
| Installation | Generally simpler | Requires control integration |
| Typical Application | Conventional laboratory ventilation | Energy-efficient laboratory ventilation |
7. Laboratory Fume Hood Airflow Testing Methods
Airflow testing is essential for verifying whether a fume hood operates according to its design and project requirements.
Measuring face velocity alone is not sufficient to confirm containment performance.
Several testing methods are commonly used.
7.1 Face Velocity Test
A calibrated anemometer is used to measure air velocity across the fume hood opening.
The opening is divided into multiple measurement areas, and readings are recorded at specified positions.
The results are used to evaluate:
Average face velocity
Velocity distribution
Local variations
Consistency across the opening
7.2 Smoke Visualization Test
Smoke visualization is used to observe airflow movement around the fume hood opening.
It helps identify:
Airflow entering the enclosure
Turbulence near the sash
Potential outward airflow
Areas of stagnant air
Effects of sash movement
Smoke testing is a qualitative method and does not independently quantify the concentration of contaminants escaping from the hood.
7.3 Tracer Gas Containment Test
Tracer gas testing is used to evaluate the containment performance of a laboratory fume hood.
A controlled tracer gas is released inside the fume hood, and specialized instruments measure the concentration near a simulated operator breathing zone.
This provides quantitative information about the hood's ability to contain airborne contaminants under specified test conditions.
7.4 Sash Movement Test
Sash movement can influence airflow and containment.
Testing evaluates how the fume hood performs when the sash is moved through different positions.
The sash should also operate smoothly and reliably.
7.5 Exhaust Airflow Measurement
The exhaust airflow volume is measured to verify whether the ventilation system provides the required air removal capacity.
Measurements can be taken at suitable locations in the exhaust system according to the applicable testing procedure.
8. ASHRAE 110 and EN 14175: Laboratory Fume Hood Standards
Two important standards frequently referenced in laboratory fume hood projects are ASHRAE 110 and EN 14175.
8.1 ASHRAE 110
ANSI/ASHRAE Standard 110 is titled:
Methods of Testing Performance of Laboratory Fume Hoods.
It provides quantitative and qualitative methods for evaluating fume hood containment performance.
The testing framework includes:
Face velocity measurements
Flow visualization
Tracer gas containment testing
It also identifies three testing conditions:
AM – As Manufactured
Evaluates the fume hood under controlled factory or test conditions.
AI – As Installed
Evaluates the fume hood after installation in the laboratory.
AU – As Used
Evaluates the fume hood under actual operating conditions, including typical equipment and laboratory activities.
These three testing conditions help distinguish the performance of the manufactured product from the performance of the installed and operating system.
8.2 EN 14175
EN 14175 is a European standard series covering laboratory fume cupboards.
Relevant parts include:
| Standard | Main Scope |
|---|---|
| EN 14175-1 | Vocabulary and definitions |
| EN 14175-2 | Safety and performance requirements |
| EN 14175-3 | Type test methods |
| EN 14175-4 | On-site test methods |
| EN 14175-6 | Variable air volume fume cupboards |
| EN 14175-7 | Fume cupboards for high heat and acidic load |
EN 14175-3 addresses laboratory testing of fume cupboard performance, while EN 14175-4 provides on-site testing methods used for commissioning, maintenance, and qualification.
The appropriate parts should be selected according to the fume hood type and project specification.
9. Common Laboratory Fume Hood Airflow Problems and Solutions

Understanding common airflow problems can help laboratory managers identify potential ventilation issues.
Problem 1: Low Face Velocity
Possible Causes:
Exhaust fan malfunction
Insufficient fan capacity
Blocked ductwork
Incorrect airflow control settings
Excessive duct resistance
Possible Solutions:
Inspect the exhaust fan.
Check ductwork for obstructions.
Verify system static pressure.
Check the airflow control system.
Arrange professional airflow testing.
Problem 2: Uneven Airflow Distribution
Possible Causes:
Poor baffle design
Incorrect baffle installation
Equipment obstructing airflow
Uneven exhaust distribution
Possible Solutions:
Inspect internal baffles.
Rearrange equipment.
Check the exhaust plenum.
Verify airflow distribution through testing.
Problem 3: Airflow Alarm Activates Frequently
Possible Causes:
Unstable exhaust pressure
Incorrect alarm settings
Building ventilation imbalance
Faulty airflow sensor
Rapid changes in sash position
Possible Solutions:
Inspect the airflow sensor.
Verify the alarm settings.
Check the exhaust fan and control system.
Coordinate the hood with the building HVAC system.
Problem 4: Smoke Escapes from the Hood
Possible Causes:
Strong cross-drafts
Incorrect sash position
Poor airflow distribution
Inadequate exhaust performance
Incorrect equipment placement
Possible Solutions:
Check nearby air supply outlets.
Reduce cross-drafts.
Review equipment placement.
Inspect internal baffles.
Arrange professional containment testing.
Problem 5: Excessive Airflow Noise
Possible Causes:
Excessive airflow
Incorrect fan selection
High duct resistance
Poor duct connections
Mechanical vibration
Possible Solutions:
Review the exhaust fan operating point.
Inspect duct connections.
Check fan mounting and vibration.
Evaluate airflow control settings.
Airflow adjustments should be performed by qualified personnel. Operators should not attempt to resolve containment problems simply by changing fan speeds or alarm settings.
10. How to Choose a Laboratory Fume Hood with the Right Airflow Performance
Before purchasing a laboratory fume hood, consider the following factors.
10.1 Identify the Chemical Applications
Determine which chemicals will be handled inside the fume hood.
Different chemical applications may require different airflow, containment, construction materials, and exhaust arrangements.
10.2 Confirm the Required Face Velocity
Discuss the specified operating face velocity with the fume hood manufacturer and laboratory ventilation engineer.
The target should be appropriate for the selected hood design and verified containment performance.
10.3 Determine the Required Exhaust Volume
Calculate the required exhaust airflow based on the working opening and selected face velocity.
Allow for the pressure losses and operating requirements of the complete exhaust system.
10.4 Check Airflow Distribution
Ask about the internal baffle design, exhaust plenum, and airflow distribution.
Uniform airflow is important for achieving suitable containment performance.
10.5 Select the Appropriate Control System
Consider whether a CAV or VAV system is more suitable for the laboratory.
The choice should account for energy consumption, operating patterns, control requirements, and building HVAC compatibility.
10.6 Confirm Monitoring and Alarm Functions
Depending on project requirements, the fume hood may include:
Digital airflow display
Low-airflow alarm
Audible warning
Visual warning
Sash position monitoring
Optional airflow control
10.7 Request Performance Test Documentation
Before purchasing, clarify which testing procedures and reports are available.
Important documentation may include:
Face velocity test results
Smoke visualization test results
Tracer gas containment test reports
Exhaust airflow measurements
Commissioning records
Applicable conformity documentation
A manufacturer should clearly distinguish factory test results from on-site performance test results.
11. Why Choose BEST LAB Laboratory Fume Hoods?
BEST LAB provides laboratory fume hoods and customized ventilation solutions for educational institutions, research facilities, pharmaceutical companies, and industrial laboratories.
Multiple Fume Hood Types
Our product range includes:
PP fume hoods
Steel fume hoods
Ducted fume hoods
Ductless fume hoods
Walk-in fume hoods
Floor-mounted fume hoods
Multi-face fume hoods
Customized Airflow Configurations
Fume hood dimensions, exhaust connections, baffle arrangements, and ventilation accessories can be configured according to project requirements.
Airflow Monitoring Systems
Depending on the selected model, available features may include airflow indicators, low-airflow alarms, and monitoring components.
Exhaust and Scrubber Solutions
BEST LAB can provide compatible exhaust fans, ductwork, and laboratory scrubber solutions according to the chemical properties and exhaust treatment requirements.
Technical Drawings and 3D Renderings
We provide technical drawings and 3D renderings to help customers review product dimensions, internal structures, utility connections, and installation arrangements before manufacturing.
Complete Laboratory Furniture Solutions
In addition to laboratory fume hoods, BEST LAB supplies laboratory workbenches, PP cabinets, chemical storage cabinets, stainless steel furniture, countertops, and other laboratory equipment.
Conclusion
Laboratory fume hood airflow is essential for effective contaminant capture and operator protection.
Face velocity, exhaust volume, airflow distribution, sash position, and room ventilation all influence fume hood performance.
However, face velocity alone cannot guarantee containment. Proper airflow design, suitable equipment installation, regular inspection, and appropriate performance testing are equally important.
When selecting a laboratory fume hood, consider the chemical applications, required airflow, ventilation control system, exhaust capacity, and applicable standards such as ASHRAE 110 and EN 14175.
A properly designed, installed, commissioned, and maintained fume hood can provide an important engineering control for laboratory safety.
Looking for laboratory fume hoods with customized airflow configurations?
BEST LAB provides PP fume hoods, steel fume hoods, ducted fume hoods, and customized laboratory ventilation solutions.
Contact BEST LAB to discuss your airflow requirements, fume hood dimensions, exhaust system, and laboratory project specifications.
Frequently Asked Questions
1. What is the recommended face velocity for a laboratory fume hood?
A commonly used design target for many conventional laboratory fume hoods is approximately 80–100 FPM (0.41–0.51 m/s). However, the appropriate value depends on the hood design, chemical hazards, operating conditions, and verified containment performance.
2. What is the difference between face velocity and exhaust volume?
Face velocity measures the speed of air entering through the fume hood opening, while exhaust volume measures the total quantity of air removed by the exhaust system over time.
3. How is fume hood face velocity measured?
Face velocity is measured using a calibrated anemometer at multiple points across the sash opening. The average of the readings is used to determine the average face velocity.
4. Does higher face velocity mean better fume hood performance?
Not necessarily. Excessive face velocity may create turbulence and negatively affect containment. Proper airflow distribution and verified containment performance are more important than simply increasing velocity.
5. What is the relationship between sash height and face velocity?
When exhaust volume remains constant, increasing sash height increases the opening area and generally reduces average face velocity. Lowering the sash generally increases average face velocity.
6. What is the difference between CAV and VAV fume hoods?
CAV systems maintain a relatively constant exhaust volume, while VAV systems adjust airflow according to sash position or other control signals.
7. What is ASHRAE 110?
ASHRAE 110 is a recognized testing standard that provides methods for evaluating laboratory fume hood containment performance through airflow visualization and tracer gas testing, among other procedures.
8. What is EN 14175?
EN 14175 is a European standard series covering laboratory fume cupboard safety, performance, type testing, and on-site testing.
9. How often should laboratory fume hood airflow be tested?
Testing frequency depends on applicable regulations, institutional policies, and risk assessments. Fume hoods should be tested during commissioning and periodically thereafter, as well as following significant changes or suspected performance problems.
10. Can BEST LAB customize laboratory fume hood airflow systems?
Yes. BEST LAB can customize fume hood dimensions, exhaust connections, ventilation accessories, and compatible scrubber arrangements according to project specifications and the intended laboratory application.
Follow Us
Any Questions? Get In Touch.
We Can Recommend Suitable Products According To Your Needs.
Other Blogs