Laboratory Fume Hood Installation: Requirements, Steps and Safety Checklist
Release time:
2026-11-21
Laboratory Fume Hood Installation: Requirements, Steps and Safety Checklist
Introduction
Proper laboratory fume hood installation is essential for maintaining laboratory safety, ventilation efficiency, and reliable equipment performance.
A laboratory fume hood is designed to capture and remove hazardous fumes, vapors, and airborne contaminants generated during chemical experiments. However, even a high-quality fume hood may not perform effectively if it is installed in an unsuitable location or connected to an improperly designed exhaust system.
Successful installation requires careful planning of laboratory space, equipment positioning, exhaust ductwork, electrical connections, ventilation capacity, and commissioning procedures.
Whether you are installing a standard laboratory fume hood, PP fume hood, steel fume hood, or walk-in fume hood, understanding the installation requirements can help prevent costly modifications and operational problems.
In this guide, we will explain laboratory fume hood installation requirements, step-by-step procedures, ventilation considerations, common installation mistakes, and a practical safety checklist.
1. Laboratory Fume Hood Installation Requirements

Before installing a laboratory fume hood, several technical and environmental factors should be evaluated.
1.1 Laboratory Space and Layout
The installation location should provide sufficient space for the fume hood, operators, laboratory equipment, and maintenance activities.
Consider the following:
Overall fume hood dimensions
Available floor space
Working aisle clearance
Sash operating space
Equipment access and transportation routes
Exhaust duct routing
Maintenance accessibility
For large or customized fume hoods, the installation area should be confirmed against approved technical drawings before production and delivery.
1.2 Suitable Installation Location
The location of a fume hood has a direct influence on its airflow and containment performance.
Recommended placement considerations include:
Avoid high-traffic areas.
Keep the hood away from frequently opened doors and windows.
Avoid direct airflow from air conditioning outlets.
Avoid locations near strong cross-drafts.
Do not obstruct emergency exits.
Avoid placing unrelated workstations directly opposite the hood opening.
Consider the interaction between adjacent fume hoods.
Air turbulence generated by nearby activities or ventilation outlets can disturb airflow at the hood opening and affect containment performance.
The final location should be reviewed by the laboratory ventilation engineer and relevant safety personnel.
1.3 Floor and Structural Requirements
The floor must provide adequate support for the complete fume hood assembly.
Before installation, check:
Floor load-bearing capacity
Floor levelness
Supporting frame stability
Anchor locations, where required
Clearance for lower cabinets and service connections
Large walk-in fume hoods and equipment-integrated models may require additional structural considerations.
1.4 Ventilation Requirements
The exhaust ventilation system must be designed according to the fume hood dimensions, operating opening, required airflow, and duct resistance.
Important parameters include:
Required face velocity
Exhaust airflow volume
Static pressure
Duct diameter
Duct length
Number of bends
Exhaust fan capacity
Laboratory make-up air supply
The exhaust system and room ventilation system should be designed together to maintain suitable airflow conditions.
2. Laboratory Fume Hood Installation Location
Choosing the right installation location is one of the most important steps in laboratory planning.
Recommended Installation Arrangement
A suitable installation arrangement should:
Provide sufficient space in front of the fume hood for operators.
Keep the hood away from busy pedestrian routes.
Avoid direct air supply from ceiling diffusers toward the sash opening.
Provide convenient access to electrical and utility connections.
Allow sufficient space for exhaust duct connections.
Maintain access for inspection and maintenance.
Locations to Avoid
| Location | Potential Problem |
|---|---|
| Near laboratory doors | Air disturbances caused by opening and closing |
| Near windows | External drafts may affect containment |
| Under air conditioning outlets | Direct airflow may disturb the hood |
| Busy walkways | Personnel movement creates turbulence |
| Near emergency exits | May obstruct evacuation routes |
| Opposite occupied workstations | Potential exposure during abnormal operations |
There is no universal installation distance suitable for every laboratory. Required clearances should be confirmed against applicable local codes, project specifications, and ventilation design requirements.
3. Fume Hood Exhaust Duct Installation

The exhaust duct system is an essential part of a ducted laboratory fume hood.
Its main function is to transport contaminated air from the fume hood to a suitable external discharge point.
3.1 Exhaust Duct Material Selection
The duct material must be compatible with the chemicals and operating conditions.
Common options include:
PP ductwork: Suitable for many compatible corrosive chemical exhaust applications.
PVC ductwork: Used in selected chemical exhaust applications after compatibility and temperature evaluation.
Stainless steel ductwork: Suitable for selected applications requiring metallic construction.
Other specialized materials: Selected according to chemical exposure and operating temperature.
Material selection should consider chemical concentration, temperature, moisture, and potential chemical reactions.
3.2 Duct Diameter and Length
The exhaust duct diameter should be determined according to the required airflow and acceptable air velocity and pressure losses.
Important considerations include:
Total duct length
Number of bends
Duct diameter
Elbows and fittings
Branch connections
Static pressure losses
An undersized duct may increase resistance and reduce the actual exhaust airflow.
3.3 Duct Routing
Good duct routing helps improve ventilation efficiency and simplifies maintenance.
Recommended practices include:
Minimize unnecessary bends.
Avoid excessive duct length.
Provide appropriate mechanical support.
Ensure connections are properly sealed.
Allow access for inspection where necessary.
Avoid unsuitable connections between incompatible exhaust streams.
Flexible connectors should only be used where permitted by the equipment design and applicable specifications.
3.4 Exhaust Fan Installation
The exhaust fan must be selected according to the complete system operating requirements.
Key specifications include:
Airflow capacity (m³/h or CFM)
Static pressure (Pa)
Motor power (kW or HP)
Fan speed (RPM)
Chemical compatibility
Operating temperature
The fan should be installed according to the manufacturer's instructions and the ventilation system design.
For many laboratory exhaust systems, the fan is located near the discharge end of the duct system to help maintain negative pressure in the ductwork. The actual arrangement depends on the building and exhaust design.
3.5 Exhaust Discharge Location
The exhaust discharge should be positioned to reduce the risk of contaminated air re-entering the building through outdoor air intakes, windows, or other openings.
The discharge arrangement must comply with applicable building and environmental requirements.
4. Electrical and Utility Connection Requirements
Laboratory fume hoods may require several electrical and utility connections.
These should be planned before the installation begins.
4.1 Electrical Connections
Electrical components may include:
LED lighting
Electrical sockets
Airflow monitoring display
Low-airflow alarm
Control panel
Exhaust fan control interface
The electrical supply must match the specified voltage, frequency, phase, and power requirements.
All electrical installation should be performed by qualified personnel in accordance with applicable electrical codes.
4.2 Water Supply and Drainage
Some fume hoods are equipped with integrated laboratory sinks and faucets.
Before installation, confirm:
Water inlet position
Water supply pressure
Drainage location
Drain pipe material
Chemical compatibility
Connection accessibility
The drainage system should be designed for the intended chemical applications and local plumbing requirements.
4.3 Gas and Other Utility Connections
Depending on laboratory requirements, additional services may include:
Laboratory gas valves
Compressed air
Vacuum connections
Specialized service outlets
All utility connections should be properly identified, tested, and installed according to the approved drawings.
5. Step-by-Step Laboratory Fume Hood Installation Process
A typical laboratory fume hood installation project can be divided into eight main stages.
Step 1: Review Technical Drawings
Before installation, review the approved drawings and specifications.
Confirm:
Overall dimensions
Installation position
Cabinet configuration
Exhaust connection location
Electrical requirements
Water and gas connections
Required installation clearances
Any discrepancies should be resolved before installation.
Step 2: Prepare the Installation Area
Ensure the laboratory is ready to receive the equipment.
Preparation includes:
Cleaning the installation area
Checking floor conditions
Confirming access routes
Preparing electrical connections
Preparing water and drainage connections
Confirming exhaust duct positions
Step 3: Unpack and Inspect the Equipment
After delivery, inspect all packages and components.
Check for:
Transportation damage
Missing accessories
Damaged glass panels
Scratched or deformed surfaces
Incorrect dimensions
Missing installation hardware
Report any issues before assembly.
Step 4: Position and Level the Fume Hood
Move the fume hood into its designated position.
Use suitable lifting and handling equipment when required.
Check:
Horizontal alignment
Vertical alignment
Supporting structure
Cabinet stability
Sash movement
Secure the equipment according to the manufacturer's installation instructions and approved structural design.
Step 5: Connect the Exhaust Ductwork
Connect the fume hood exhaust outlet to the designated duct system.
Check:
Duct diameter
Connection compatibility
Joint sealing
Mechanical support
Exhaust fan connection
Airflow direction
All duct connections should be inspected before operation.
Step 6: Complete Electrical and Utility Connections
Install and connect the electrical components, water supply, drainage, and other services.
Verify that all connections correspond to the approved technical drawings.
Step 7: Start the Ventilation System
Before using the fume hood, start the exhaust system and verify its operating conditions.
Check:
Exhaust fan operation
Airflow direction
Airflow monitoring display
Alarm functions
Sash operation
Room ventilation balance
Adjustments should be performed by qualified ventilation technicians.
Step 8: Perform Commissioning and Acceptance Testing
The final stage is to verify that the installed fume hood meets the project requirements.
Testing may include:
Face velocity measurement
Airflow visualization
Exhaust airflow measurement
Sash operation inspection
Alarm function testing
Tracer gas containment testing, where specified
The fume hood should only be released for laboratory use after the required commissioning and acceptance procedures have been completed.
6. Laboratory Fume Hood Commissioning and Testing
Commissioning confirms that the fume hood and its ventilation system operate correctly after installation.
6.1 Face Velocity Test
Measure the average air velocity across the sash opening using a calibrated anemometer.
The test should follow the specified measurement procedure and operating sash position.
The acceptance range should be established according to the selected fume hood design, project specification, and applicable requirements.
6.2 Smoke Visualization Test
Smoke visualization helps demonstrate airflow behavior at the fume hood opening.
It can identify:
Inward airflow
Air turbulence
Stagnant areas
Potential outward airflow
Effects of sash movement
6.3 Exhaust Airflow Test
Measure the exhaust airflow volume to confirm that the system provides the required air removal capacity.
Compare the actual result with the approved ventilation design.
6.4 Tracer Gas Containment Test
For projects requiring quantitative containment verification, tracer gas testing can be performed according to the specified test standard.
ANSI/ASHRAE Standard 110 provides recognized methods for evaluating laboratory fume hood performance.
6.5 Alarm and Control System Test
Check the operation of:
Low-airflow alarm
Visual warning
Audible warning
Digital airflow display
Sash monitoring, where installed
6.6 Documentation and Acceptance
Prepare the relevant commissioning documents, including:
Installation inspection records
Face velocity test report
Smoke visualization test report
Exhaust airflow measurement
Alarm function test
Tracer gas test report, where applicable
Operation and maintenance instructions
7. Common Laboratory Fume Hood Installation Mistakes
Incorrect installation can reduce ventilation performance and create unnecessary safety risks.
| Common Mistake | Possible Consequence | Recommended Solution |
|---|---|---|
| Installing near doors | Air turbulence | Select a more suitable location |
| Installing under air diffusers | Unstable airflow | Coordinate HVAC layout |
| Undersized exhaust duct | Insufficient airflow | Recalculate duct dimensions |
| Incorrect fan selection | Poor exhaust performance | Calculate airflow and static pressure |
| Incompatible duct materials | Chemical deterioration | Review chemical compatibility |
| Poor duct sealing | Exhaust leakage | Inspect and seal connections |
| Insufficient make-up air | Room pressure imbalance | Coordinate supply and exhaust systems |
| Incorrect electrical supply | Equipment malfunction | Confirm electrical specifications |
| No commissioning test | Unverified performance | Complete acceptance testing |
8. Laboratory Fume Hood Installation Safety Checklist
Before handing over a newly installed fume hood, use the following checklist.
Installation Preparation
Approved technical drawings reviewed.
Installation location confirmed.
Floor conditions checked.
Installation access confirmed.
Electrical and utility connections prepared.
Exhaust duct route confirmed.
Mechanical Installation
Fume hood positioned correctly.
Equipment leveled and secured.
Glass sash installed correctly.
Internal baffles checked.
Exhaust duct connections completed.
All mechanical connections inspected.
Electrical and Utility Connections
Electrical supply verified.
Lighting tested.
Electrical sockets inspected.
Water supply tested, where installed.
Drainage connections inspected.
Gas and other utility connections tested, where installed.
Ventilation and Commissioning
Exhaust fan operating correctly.
Airflow direction verified.
Face velocity measured.
Smoke visualization completed.
Exhaust airflow checked.
Airflow alarm tested.
Tracer gas test completed, if required.
Commissioning documents prepared.
Final Handover
Installation inspection completed.
Operating instructions provided.
Maintenance instructions provided.
Required test reports submitted.
Customer acceptance completed.
9. Laboratory Fume Hood Installation Standards
When planning a laboratory fume hood installation project, the applicable safety and performance standards should be confirmed.
ANSI/ASHRAE Standard 110
ASHRAE 110 provides methods for testing laboratory fume hood performance.
It is commonly referenced for evaluating:
Face velocity
Airflow visualization
Tracer gas containment performance
EN 14175
EN 14175 is a European standard series covering laboratory fume cupboard safety and performance.
Relevant parts include:
EN 14175-2: Safety and performance requirements
EN 14175-3: Type test methods
EN 14175-4: On-site test methods
EN 14175-4 is particularly relevant to installation commissioning and on-site performance testing.
Other Applicable Requirements
Depending on the country and project, additional requirements may include:
NFPA 45 – Fire Protection for Laboratories Using Chemicals
ANSI/AIHA Z9.5 – Laboratory Ventilation
Local building codes
Local electrical regulations
Environmental exhaust discharge requirements
The applicable standard editions and acceptance criteria should be confirmed with the project engineer and local authorities.
10. BEST LAB Laboratory Fume Hood Installation Support
BEST LAB provides laboratory fume hoods and customized laboratory ventilation equipment for international laboratory projects.
Our product range includes:
Standard Laboratory Fume Hoods
PP Fume Hoods
Steel Fume Hoods
Ductless Fume Hoods
Walk-In Fume Hoods
Floor-Mounted Fume Hoods
Multi-Face Fume Hoods
Customized Product Design
We provide customized dimensions, materials, sash configurations, worktops, and accessories according to project specifications.
Technical Drawings
Detailed technical drawings help customers confirm product dimensions, utility positions, and exhaust connections before production.
3D Laboratory Renderings
3D renderings help visualize the fume hood within the overall laboratory layout and coordinate it with laboratory workbenches and storage cabinets.
Exhaust System Solutions
Compatible exhaust fans, ductwork, and PP scrubber systems can be considered according to chemical applications and ventilation requirements.
Complete Laboratory Furniture Solutions
In addition to fume hoods, BEST LAB supplies laboratory benches, wall cabinets, base cabinets, chemical storage cabinets, PP furniture, and stainless steel laboratory furniture.
Contact BEST LAB for customized laboratory fume hood solutions and technical support for your next laboratory project.
Conclusion
Proper laboratory fume hood installation requires careful coordination of equipment positioning, ventilation design, exhaust ductwork, electrical connections, and commissioning procedures.
A suitable installation location, correctly selected exhaust fan, compatible duct materials, and adequate make-up air are essential for reliable fume hood operation.
However, installation alone does not guarantee performance. Each fume hood should undergo appropriate commissioning and testing before being released for laboratory use.
By following the correct installation procedures and safety checklist, laboratory owners and project contractors can improve ventilation reliability and support a safer working environment.
Looking for a reliable laboratory fume hood manufacturer?
BEST LAB provides customized laboratory fume hoods, exhaust systems, PP scrubbers, and complete laboratory furniture solutions for research, educational, pharmaceutical, and industrial laboratories.
Contact our team to discuss your laboratory layout, fume hood specifications, and project requirements.
Frequently Asked Questions
1. Where should a laboratory fume hood be installed?
A laboratory fume hood should be installed away from high-traffic areas, doors, windows, and direct air conditioning outlets to minimize airflow disturbances.
2. How much space is required for fume hood installation?
The required space depends on the hood dimensions, sash opening, operator clearance, duct connections, and maintenance access. Always refer to the approved installation drawings.
3. Does a laboratory fume hood require an exhaust fan?
A conventional ducted fume hood requires a suitable exhaust fan to transport contaminated air through the ductwork to an appropriate discharge point.
4. What material should be used for fume hood exhaust ducts?
PP, PVC, stainless steel, and other specialized materials may be used depending on the chemicals, temperatures, and exhaust conditions. Chemical compatibility must be evaluated before selection.
5. Can a fume hood be installed near an air conditioning outlet?
Direct airflow from an air conditioning outlet may disturb the airflow at the fume hood opening. It is preferable to locate the hood away from direct supply air jets.
6. What is make-up air in a laboratory?
Make-up air is replacement air supplied to the laboratory to compensate for the air removed by fume hoods and other exhaust systems. It helps maintain the intended room pressure and ventilation balance.
7. How long does laboratory fume hood installation take?
Installation time depends on the fume hood size, number of units, site preparation, ductwork, electrical connections, and utility requirements. The schedule should be confirmed for each project.
8. What tests are required after installation?
Common commissioning tests include face velocity measurement, smoke visualization, exhaust airflow measurement, alarm testing, and tracer gas containment testing when specified.
9. Is ASHRAE 110 required for every fume hood installation?
Not universally. ASHRAE 110 testing is required when specified by the project, institutional requirements, or applicable regulations. It is a recognized method for evaluating fume hood performance.
10. Does BEST LAB provide customized laboratory fume hoods?
Yes. BEST LAB provides customized fume hoods in different materials, sizes, configurations, and ventilation arrangements according to laboratory project requirements.
Follow Us
Any Questions? Get In Touch.
We Can Recommend Suitable Products According To Your Needs.
Other Blogs